Tel: 540-450-8375 | Email: info@hi-lite.com

Better Solutions = Better Finish™

 

Sherwin-Williams line of AEROGREEN Specialty Cleaners, manufactured by Hi-Lite Solutions, gives you the tools to safely clean and prepare almost any surface for a finished coat of paint. Sherwin-Williams understands how important it is to properly clean and prepare a surface prior to painting to ensure the best bond between the coating and the surface. The vast majority of coating failures can be directly attributed to inadequate surface preparation, which affects coating adhesion.

It’s just as important to Sherwin-Williams that the products they sell are environmentally sound, cost effective and safe solutions that reduce any negative impact on the environment, while providing equal or better performance than their traditional toxic counterparts. So how do you get the best finish possible, and still ‘Go Green’? It’s simple … prep the job with AEROGREEN’s highly effective, eco-friendly, water based paint prep cleaners and degreasers listed below, and finish the job with Sherwin-Williams products.

4110 Paint Prep Cleaner

In order to Go Green, and reduce VOC’s in the paint industry, solvent based paints are rapidly being replaced by water-based paints. AEROGREEN’s 4110 Paint Prep Cleaner, the first non-toxic, water-based product on the market designed to safely clean and prepare all surfaces for paint, works better than traditional toxic cleaners with the industry’s new paints. Because the paint and AEROGREEN 4110 both use water based technology, there are very compatible, so the paint bonds better to the surface, leaving little or no imperfections in the painted surface. 

SW PART NUMBERS

32 Ounce   – SW592-2810
Gallon        – SW592-2828
5 Gallon     – SW592-2554
55 Gallon   – SW592-2802
330 Gallon – SW592-2836

Datasheets – Industrial / Automotive | SDS | Certifications

4110 Ready Wipes

AEROGREEN® is the best way of cleaning metal of oils, dirt, grease, waxes, polishing compounds, salts, soluble oils, drilling and cutting compounds and other surface contaminants that will prevent the cuttings from adhering to metal surfaces as outlined in SSPC-SPI International Standards. AEROGREEN® is for use as a Pre-Paint Cleaner prior to coatng, in-between primer and top coat, and as a final clean to make items customer ready. The most common method of surface Preparation is solvent wipe-on, wipe-off. AEROGREEN® 4110 RW Paint Prep is a drop in replacement for solvent type cleaners such as Lacquer thinner, MIBK, MEK, IPA, Acetone and other hazardous high VOC solvents.

SW PART NUMBERS

Gallon 4-per case   – SW1013-11306

Datasheets – Industrial / Automotive / Wood | SDS | Certifications

4130 High Pressure Cleaner Degreaser

AEROGREEN® 4130 High Pressure Cleaner Degreaser, is a concentrated cleaner used to prepare large surfaces such as exterior buildings, interior walls, ceilings, floors and stairways, for paint. When used with both cold and heated high pressure washers, quickly breaks down and safely removes dirt, concrete dust, exhaust soot, oils, greases, hydraulic fluids and fuel residue, as well as a variety of soils, leaving a residue free clean surface ready to be painted. It’s recommended that after using AEROGREEN® 4130, you give metal doors, window frames and railings, a quick wipe with AEROGREEN® 4110 before painting.

SW PART NUMBERS

Gallon        – SW592-2851
5 Gallon     – SW592-2885
55 Gallon   – SW592-2919
330 Gallon – SW592-2927

Datasheet | SDS | Certifications

4160 Parts Washer Degreaser

AEROGREEN® 4160 Parts Washer Degreaser is designed to provide superior cleaning of mechanical parts, engine support equipment and automotive components that are to be painted. AEROGREEN® 4160 is mixed with water in a dip or immersion tank, ultrasonic tank, or in-line system, then the pieces to be painted are cleaned in the solution, and set aside until it’s time to paint. The solution can last for weeks depending on the frequency of use and the size of the tank. AEROGREEN® 4160 contains a rust inhibitor, so that the part can be worked on or shelved for some time before painting without any corrosion forming on the surface. The part would get a final wipe down with AEROGREEN® 4110 to remove any surface dust or dirt right before it’s painted.

SW PART NUMBERS

5 Gallon     – SW592-2950
55 Gallon   – SW592-2976
330 Gallon – SW592-2984

Datasheet | SDS | Certifications

4175 UV Line and Roll Coater Cleaner

Roll coating machines are commonly used for the application of a liquid to the surface of a part. Roll coaters can be used to apply liquid adhesives, paints, oils, and coatings such as varnish or clear finish coats. Roll coaters can take many forms, from simple paint rollers to sophisticated coating machines with multiple rollers. For the line to continue to run at a constant speed the various parts of the roll coater must be constantly cleaned. Acetone and other hazardous solvents have been the standard cleaning solution for these units, AEROGREEN 4175 was developed as a direct drop-in replacement for use in industries such as industrial wood, cabinet makers, wood flooring manufacturers, aluminum, paper, card stock, wall paper, magazines, glass and plastics.

SW PART NUMBERS

1 Gallon     – SW943-3715
5 Gallon     – SW592-2992

55 Gallon   – SW592-3057
330 Gallon – SW592-3073

Datasheet | SDS

4180 Paint & Graffiti Remover

AEROGREEN 4180 PAINT REMOVER is a liquid paint remover developed to remove most industrial, water reducible paints and primers including, lacquers, acrylic enamels, solvent based alkyd paints, high & low gloss urethanes, epoxy paints, powder coat paints, inks, adhesives and a variety of other coatings from many types of substrates including steel, cast iron, aluminum, concrete, masonry, and plastics. AEROGREEN 4180 PAINT REMOVER works by penetrating through the old coating to break the bond of the coating to the substrate instead of dissolving the coating. This process, called delaminating, is not only safer to use, but allows easier collection of the residue for more efficient residue clean up and disposal.

SW PART NUMBERS

Gallon        – SW1005-19388
5 Gallon     – SW1004-44470

DatasheetSDS

AC-10 Rust Remover and Metal Prep

AEROGREEN® AC-10 Rust Remover and Metal Prep is specially formulated to remove rust or any type of oxidation on the surface of a metal part prior to painting. Depending on the surface to be cleaned, this clear, odorless, innovative product can be diluted with water and brushed on, sprayed on, or used in cold or heated dip tanks for the best results. AEROGREEN® AC-10 is also used when a part has been welded prior to painting. The welded area of the part is wiped down with AEROGREEN® AC-10 to prep the metal. After removing rust or prepping the metal with AEROGREEN® AC-10, the part is given a final wipe down with AEROGREEN® 4110 prior to painting.

SW PART NUMBERS

1 Gallon     – SW938-8927
5 Gallon     – SW592-3081

55 Gallon   – SW592-3099
330 Gallon – SW592-3107

Datasheet | SDS

AC-10 Ready Wipes Rust Remover and Metal Prep

AEROGREEN® AC-10 Ready Wipes Rust Remover and Metal Prep is a phosphoric acid and detergent blend formulated to clean metal surfaces, remove rust, and profile steel, cast iron, galvanized metals, zinc, high polished aluminum prior to paint or to prepare a surface for a subsequent chemical coating, including liquid, and powder coating finishing systems. For use in Wipe on Wipe off Preparation of Surface Prior to Painting. The rust must be removed to prepare the surfaces prior to painting or applying new protective coatings or the rust will continue to grow under the coating. Ideal for all Industrial, Automotive, Agriculture, Transportation Industries and Marine Industries.

SW PART NUMBERS

1 Gallon Tub – 4 per Crate     – SW1015-59540

Datasheet | SDS

Introducing our NEW Natural World Floor Surface Cleaners and Maintenance Oils

4200 Wood Floor Maintenance Oil

AEROGREEN® 4200 WOOD FLOOR MAINTENANCE OIL keeps the natural beauty of oiled wood floors, while maintaining and protecting the floor with a unique blend of natural oils that penetrate into the wood, highlighting the natural grain while providing lasting protection. AEROGREEN® 4200 contains no solvents or hazardous chemicals and can be applied by hand with a clean cloth, clean mop, lambs wool pad or paint roller. All applicator tools can be cleaned out with plain soap and water.

Datasheet | SDS

4210 Revitalizer Oil for Wood Floors

AEROGREEN® 4210 REVITALIZER OIL FOR WOOD FLOORS is used for regular cleaning and maintenance of oiled floors to enhance the nautral beauty. AEROGREEN® 4210 penetrates into the wood and provides the surface with a protective finish, while adding essential oils to nourish the wood as you clean. AEROGREEN® 4210 contains no solvents or hazardous chemicals and has a light, pleasant odor, it can be easily applied by hand with a clean mop or lambs wool pad.

Datasheet | SDS

4220 Wood Floor Cleaner

AEROGREEN® 4220 WOOD FLOOR CLEANER is a safe and effective ready to use cleaner that provides a complete clean to wood floors by gently and effectively removing dust, dirt and grime. AEROGREEN® 4220 dries fast leaving no dulling residue, just spray and mop… no rinsing necessary. AEROGREEN® 4220 is safe for all hardwood, laminate, unwaxed and polyurethane finished wood floors, and is a non-toxic, low VOC waterborne formula that’s better for the environment.

DatasheetSDS